davidluopf

Le blog de davidluopf

Relationship between material humidity and Raymond mill output

Because Raymond Mill is a grinding equipment used to process ore, there is a certain requirement for the humidity of the material. If the humidity is too high, what effect does it have on the production of Raymond Mill? The following is the analysis of the relationship between material humidity and Raymond mill output by Zhengzhou Shuguang.
http://www.zzsgchina.com
Raymond mill has a range of requirements for milling materials, that is, Mohs hardness below 9.3, and humidity is not more than 6%. If it exceeds this range, it will affect the working efficiency of the mill, which requires us to When using the mill, it is necessary to select different equipment according to different models, and the materials that do not meet the requirements are processed first, and then the Raymond mill is used for the grinding operation.
Generally speaking, the humidity of the material is too large. In the grinding operation, the material will stick together and the clogging phenomenon will occur, or the material will be bonded with the grinding roller, the grinding ring, etc., hindering the grinding machine. Grinding, which causes the mill to fail to perform normal work. Therefore, when using the Raymond mill, the material must be strictly checked. Only after the material meets the production standards can the Raymond machine perform its performance, thereby effectively increasing the output and working efficiency of the Raymond mill.
publié le lundi 10 décembre à 00:53, aucun commentaire.

Solution to Rust of Parts of Shredding Machine

The shredder must be stored in an indoor dry place, so as to effectively prevent the shredder from rusting due to the oxidation of water. But what if the shredder is rusty?
http://www.sg-shredder.com
The first thing we need to see is which parts of the shredder are rusted. If the shell has no great influence on the operation of the shredder itself, we can refuel after washing to prevent rust, or use other methods to remove rusty parts and prevent them from rusting again.
If the important parts of the shredder, such as bearings, are rusty, then we should pay attention to it, because this may lead to a slower work efficiency of the shredder, will make the friction greater, easy to cause internal wear and tear, at this time we have to rust first, and then add lubricant for maintenance. If some parts are seriously rusted, we can consider replacing rusty parts and using new parts to produce them to ensure the normal operation of the shredder.
publié le lundi 10 décembre à 00:52, aucun commentaire.

How does the micronized powder machine discharge materials?

In actual production, the material is not free to leave the micronized powder mill from the discharge end. The discharge end of the micronized mill has the effect of suppressing the discharge of large particles, and the small particles can be discharged smoothly, while the large particles remain in the discharge. The mill continues to be ground, a function known as outlet grading. This function of the mill itself affects the time the material stays in the mill, and the different discharge modes have different inhibitory effects. In modeling, if you ignore this function, the large particle content of the model prediction value will be too large. To reflect this functionality, there are four ways to handle it:
http://www.sgzgchina.com
1. Introduce a classification function in the model of the mill and return the graded return sand directly to the inlet of the mill.
2. Different axial speeds are used for different particle sizes to indicate the advancement of the particles within the mill, and thus may be equivalent to returning the graded return sand to the inlet of each mixer.
3. The expression of the crushing rate is modified. The idea of this method is that the large particles are inhibited from being discharged, which means that the average residence time of the large particles is long. Therefore, if the residence time of the large particles is the same as the residence time of other particles, At the same time, the breaking rate of large particles is accelerated and the breaking rate of small particles is slowed, which will achieve the same effect as the long residence time of large particles. This method is the same as the pseudo-time method.
4. The non-first-order crushing rate is adopted and the crushing rate increases with time, and the breaking rate of the large particles is increased faster, and the breaking rate of the small particles is increased more slowly, thereby achieving the large particle residence time. Longer same effect.
publié le lundi 10 décembre à 00:46, aucun commentaire.

Plastic film shredder equipment processing technology

The plastic film shredder equipment is driven by double shaft independent, so that the material is correspondingly pressed during production to achieve the automatic feeding function. The unique cutter shaft structure and the four-corner rotary cutter can improve the production efficiency in the process of low-speed and high-torque production without twisting the shaft or jamming the equipment.
http://www.zzshuguangchina.com/news/news_industry/Plastic-film-shredder-equipment-processi.html
The plastic shredder equipment processing technology, the waste plastic film is directly sent into the machine cavity by machinery. Through the motor → transmission reducer → drive spindle, the movable knife installed on the main shaft and the fixed knife installed on the frame, the whole bundle of waste plastic film is put into the machine cavity, and shredded to reach the recyclable raw materials.
As a leader in the plastic film shredder equipment industry, Shuguang Machinery is constantly making progress and is investing heavily in the research and development of new technologies. The development of high-tech content, the pace of renewal and replacement is accelerating year by year, using new technology to produce plastic film shredder equipment in line with social needs, has many advantages in production, environmental protection, recycling and other aspects.
publié le lundi 10 décembre à 00:44, aucun commentaire.

Correct use steps of Raymond Mill

Any kind of equipment has a set of corresponding specifications and instructions. Of course, Raymond machine is no exception. Raymond mill is a kind of milling equipment commonly used in the mining mill industry. After the user purchases the equipment and installs it, the first thing to pay attention to is the operation method of the equipment specification. Only by developing a good standard operation can the equipment be operated smoothly and the production efficiency of the Raymond mill can be effectively guaranteed.
http://www.zzsgchina.com
1. After the installation of Raymond Mill, the first step is to carry out no-load and on-load operation to test the stability of the equipment. The second process is mainly used to check the operation of components such as bearings, bolts, flywheels, etc., and whether there is abnormal noise inside the equipment. If there is an abnormal phenomenon, it needs to be shut down in time for treatment.
2. When starting the Raymond mill, be sure to follow the correct boot sequence, and also observe and control the system current when starting. If the device current just starts, it will rise sharply, which is a transient phenomenon. However, if the current is high for a long time, stop it immediately and check the equipment and circuit.
3. During the use of Raymond mill, some wearing parts will often wear out, so regular inspection and replacement are required for these wearing parts. And pay attention to the size of the material when feeding, if the material is too large, it can not be produced, it needs to be processed before the grinding operation, and it is necessary to ensure continuous and uniform feeding when feeding, so that it can get good. Production efficiency.
4. There is also an important point. When using Raymond mill, you must pay attention to the maintenance and maintenance of Raymond machine. These need to be assigned to take care of the whole machine. During the maintenance period, the power of the whole machine should be turned off to ensure the safety of maintenance.
publié le samedi 08 décembre à 05:29, aucun commentaire.

Correct use steps of Raymond Mill

Any kind of equipment has a set of corresponding specifications and instructions. Of course, Raymond machine is no exception. Raymond mill is a kind of milling equipment commonly used in the mining mill industry. After the user purchases the equipment and installs it, the first thing to pay attention to is the operation method of the equipment specification. Only by developing a good standard operation can the equipment be operated smoothly and the production efficiency of the Raymond mill can be effectively guaranteed.
http://www.zzsgchina.com
1. After the installation of Raymond Mill, the first step is to carry out no-load and on-load operation to test the stability of the equipment. The second process is mainly used to check the operation of components such as bearings, bolts, flywheels, etc., and whether there is abnormal noise inside the equipment. If there is an abnormal phenomenon, it needs to be shut down in time for treatment.
2. When starting the Raymond mill, be sure to follow the correct boot sequence, and also observe and control the system current when starting. If the device current just starts, it will rise sharply, which is a transient phenomenon. However, if the current is high for a long time, stop it immediately and check the equipment and circuit.
3. During the use of Raymond mill, some wearing parts will often wear out, so regular inspection and replacement are required for these wearing parts. And pay attention to the size of the material when feeding, if the material is too large, it can not be produced, it needs to be processed before the grinding operation, and it is necessary to ensure continuous and uniform feeding when feeding, so that it can get good. Production efficiency.
4. There is also an important point. When using Raymond mill, you must pay attention to the maintenance and maintenance of Raymond machine. These need to be assigned to take care of the whole machine. During the maintenance period, the power of the whole machine should be turned off to ensure the safety of maintenance.
publié le samedi 08 décembre à 05:27, aucun commentaire.

  Page suivante

Publicité